5-in-1 QAV Quadcopter PDB-Board

5-in-1 QAV Quadcopter PDB-Board

$13.90
(No reviews yet) Write a Review

Frequently Bought Together

HOBBYMATE 5-in-1 QAV Quadcopter PDB-Board-BEC 5V/3A-12V, LED Light Controller, Flyaway Finder & Battey Low Voltage Alarm

Product Description:

  • Specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
  • Simplify wiring. The BEC 12V can be used to power the Camera, Video Transmitters,ect.
  • Inbuilt 5V LED light controller, three flash modes can be choosed with the toggle switch of transmiter.
  • Toggle the switch to trigger the buzzer beep crazy to help you find lost quad or flexed wing in tall grass or trees, this could be very helpful when crash.
  • You could also connect it to three flash modes 5v led to achieve better effect. It also acts as a battery voltage monitor ; Once voltage gets below preset threshold , the buzzer & LED light will alert you.

Features:

  • Built-in 5 functions, small size & light weight,2oz copper & 4-layers PCB. ESC & Battery solder tabs in pairs.
  • BEC 5V / 12V Output LED indicators. TVS input protection Input voltage: 9 ¨C 26VDC, support 3S-6S lipo battery
  • 1 Battery input & 4 ESC outputs. Regulated 5V and 12V outputs.LED power indicators (5V & 12V outputs) 4 pairs
  • 5V LED light pads.Low voltage setting value indicators
  • Dimensions: 46x36x6mm ;
  • Weight: 9g ; Mounting holes
  • 30.5mm square spacing.
  • F1. PDB (ESC outputs)
  • F2. BEC 5V output Designed for RC Receivers, Flight controllers, OSD, and Servos.
  • DC/DC synchronous buck regulator,Voltage: 5.0 +/- 0.1VDC.
  • Continuous current: 3 Amps.
  • Short-circuit tolerant (10 seconds/minute).5V is also on the Aux pins + & -.
  • If other 5V BEC in use, Pls remove the red wire on Aux pins.
  • F2. BEC 12V output Linear regulator, very low noise.Standard output designed to power cameras and video transmitters,etc.
  • If the battery is 3S LiPo, Output voltage=3S LiPo voltage ¨C 1V.
  • Don¡¯t use BEC 12V to power VTX or Gimbals when 6S battery is in use.
  • F3. LED Light Controller Total 4 pairs LED light pads, All the LED lights have the same status.
  • LED light voltage should be 5V.
  • Pls use the Aux channel with toggle switch of three positions.
  • Middle position is OFF (Value=1400~1600). Side position is LED ON (Value=1700~2000).
  • Three LED modes: Constant light, Slow flash(1Hz), Fast flash(3Hz)
  • F4. Lost Plane Finder
  • F5. Low Voltage Alarm Notify you once the cells reach preset voltage.

Package includes:

  • 1 x Hobbymate 5 in 1 PDB Board

HOBBYMATE 5-in-1 QAV Quadcopter PDB-Board-BEC 5V/3A-12V, LED Light Controller, Flyaway Finder & Battey Low Voltage Alarm

Product Description:

  • Specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
  • Simplify wiring. The BEC 12V can be used to power the Camera, Video Transmitters,ect.
  • Inbuilt 5V LED light controller, three flash modes can be choosed with the toggle switch of transmiter.
  • Toggle the switch to trigger the buzzer beep crazy to help you find lost quad or flexed wing in tall grass or trees, this could be very helpful when crash.
  • You could also connect it to three flash modes 5v led to achieve better effect. It also acts as a battery voltage monitor ; Once voltage gets below preset threshold , the buzzer & LED light will alert you.

Features:

  • Built-in 5 functions, small size & light weight,2oz copper & 4-layers PCB. ESC & Battery solder tabs in pairs.
  • BEC 5V / 12V Output LED indicators. TVS input protection Input voltage: 9 ¨C 26VDC, support 3S-6S lipo battery
  • 1 Battery input & 4 ESC outputs. Regulated 5V and 12V outputs.LED power indicators (5V & 12V outputs) 4 pairs
  • 5V LED light pads.Low voltage setting value indicators
  • Dimensions: 46x36x6mm ;
  • Weight: 9g ; Mounting holes
  • 30.5mm square spacing.
  • F1. PDB (ESC outputs)
  • F2. BEC 5V output Designed for RC Receivers, Flight controllers, OSD, and Servos.
  • DC/DC synchronous buck regulator,Voltage: 5.0 +/- 0.1VDC.
  • Continuous current: 3 Amps.
  • Short-circuit tolerant (10 seconds/minute).5V is also on the Aux pins + & -.
  • If other 5V BEC in use, Pls remove the red wire on Aux pins.
  • F2. BEC 12V output Linear regulator, very low noise.Standard output designed to power cameras and video transmitters,etc.
  • If the battery is 3S LiPo, Output voltage=3S LiPo voltage ¨C 1V.
  • Don¡¯t use BEC 12V to power VTX or Gimbals when 6S battery is in use.
  • F3. LED Light Controller Total 4 pairs LED light pads, All the LED lights have the same status.
  • LED light voltage should be 5V.
  • Pls use the Aux channel with toggle switch of three positions.
  • Middle position is OFF (Value=1400~1600). Side position is LED ON (Value=1700~2000).
  • Three LED modes: Constant light, Slow flash(1Hz), Fast flash(3Hz)
  • F4. Lost Plane Finder
  • F5. Low Voltage Alarm Notify you once the cells reach preset voltage.

Package includes:

  • 1 x Hobbymate 5 in 1 PDB Board
No reviews yet.

People who viewed this item also viewed

Compare