HOBBYMATE 5" FPV Racing Drone Kits / PNP

HOBBYMATE 5" FPV Racing Drone Kits / PNP

$239.90 $189.90
(No reviews yet) Write a Review

Frequently Bought Together

HOBBYMATE 5" FPV Racing Drone Kits / PNP / BNF

HobbyMate Comet VX220 highlights
Low-deck, stretched-X design;
Rugged 5mm carbon-fiber frame;
220mm sized carbon fiber frame (thickness 5mm);
Airbot F4 V6 flight controller; Support 3-6s lipo power
Airbot Furling32 F3 4-in-1 45A ESC;Support 3-6s lipo power
HOBBYMATE 2305 FPV racing motors (2500KV or 1800KV);
Dalprop 5045 / Gemfan 5152 3-leaf propeller (NOT INCLUDED)
Foxeer Arrow Micro Pro 600TVL FPV Camera;
Switchable 0~600 mW 5.8G Video transmitter w/ microphone (VTx);
Standard XT60 connectors soldered on ESC
Solid 5mm carbon fiber arms, 2mm top plate
3 hole configuration to hold the motors
3D Printing antenna holder

Weight 304 grams w/ o battery

Hobbymate full range receiver compatible with Frsky Radio Transmitter
http://hobbycool.com/full-range-s-bus-receiver-16-ch-support-lua-script-w-s-port-telemetry/

hobbymate-comet-review-wiring.jpg

comet-assebling-diagrame.jpg
Due to the switchable broadcast power, the FPV range is not an issue. The 48 channels VT5804 VTX can be set to 600 mW transmission power if needed. Both, frequency and power can be adjusted through the on-board control button as well as remotely via your transmitter (IRC Tramp works after FC-VTX wiring is done properly).

Thanks to the on-board microphone, using a compatible FPV headset, you can hear the noise of the four powerful brushless motors. That’s the ultimate immersive FPV flight experience.

As the battery is attached under the belly of the drone, there is enough room on top for a second DVR camera (whether GoPro Session or Foxeer Legend alike).

Initial setup
First off all: Do not power ON the Comet drone with installed propellers till everything is configured properly and double checked in Betaflight Configurator, although we did all of the configuration. Also, prior any setup process always read the product’s manual! You can also refer to Hobbymate youtube channel for more video instructions

The main difference between PNP and BNF package, is that while BNF requires only binding process, PNP requires also radio receiver installation & wiring.

Binding example with Taranis Q X7 transmitter
Firstly, create a new model on my transmitter and name it “Comet”. Secondly, under the “Model setup” screen, I set “Internal RF” and operation mode to “D16”. After these two steps you can selected the “Bind” option. When the Taranis Q X7 enters into “Bind” state it makes a high-pitched beeping.

 

 

HOBBYMATE 5" FPV Racing Drone Kits / PNP / BNF

HobbyMate Comet VX220 highlights
Low-deck, stretched-X design;
Rugged 5mm carbon-fiber frame;
220mm sized carbon fiber frame (thickness 5mm);
Airbot F4 V6 flight controller; Support 3-6s lipo power
Airbot Furling32 F3 4-in-1 45A ESC;Support 3-6s lipo power
HOBBYMATE 2305 FPV racing motors (2500KV or 1800KV);
Dalprop 5045 / Gemfan 5152 3-leaf propeller (NOT INCLUDED)
Foxeer Arrow Micro Pro 600TVL FPV Camera;
Switchable 0~600 mW 5.8G Video transmitter w/ microphone (VTx);
Standard XT60 connectors soldered on ESC
Solid 5mm carbon fiber arms, 2mm top plate
3 hole configuration to hold the motors
3D Printing antenna holder

Weight 304 grams w/ o battery

Hobbymate full range receiver compatible with Frsky Radio Transmitter
http://hobbycool.com/full-range-s-bus-receiver-16-ch-support-lua-script-w-s-port-telemetry/

hobbymate-comet-review-wiring.jpg

comet-assebling-diagrame.jpg
Due to the switchable broadcast power, the FPV range is not an issue. The 48 channels VT5804 VTX can be set to 600 mW transmission power if needed. Both, frequency and power can be adjusted through the on-board control button as well as remotely via your transmitter (IRC Tramp works after FC-VTX wiring is done properly).

Thanks to the on-board microphone, using a compatible FPV headset, you can hear the noise of the four powerful brushless motors. That’s the ultimate immersive FPV flight experience.

As the battery is attached under the belly of the drone, there is enough room on top for a second DVR camera (whether GoPro Session or Foxeer Legend alike).

Initial setup
First off all: Do not power ON the Comet drone with installed propellers till everything is configured properly and double checked in Betaflight Configurator, although we did all of the configuration. Also, prior any setup process always read the product’s manual! You can also refer to Hobbymate youtube channel for more video instructions

The main difference between PNP and BNF package, is that while BNF requires only binding process, PNP requires also radio receiver installation & wiring.

Binding example with Taranis Q X7 transmitter
Firstly, create a new model on my transmitter and name it “Comet”. Secondly, under the “Model setup” screen, I set “Internal RF” and operation mode to “D16”. After these two steps you can selected the “Bind” option. When the Taranis Q X7 enters into “Bind” state it makes a high-pitched beeping.

 

 

No reviews yet.

Videos Hide Videos Show Videos

People who viewed this item also viewed

Compare