HOBBYMATE Flash Hybrid 5" FPV Racing Drone Kits / PNP / BNF
Note:
Kits comes with frame, electronics parts, NO receiver, not assembled.
PNP version will be pre-assembled, without receiver installed.
BNF version will be assembled with receiver which is compatible with Frsky Radio and Jumper transmitter.
- Kits building Video and Configuration of flight pack
CultureFPV Review Video:
Frame Spec:
-215mm 5" Racing Platform
-Full 3k carbon fiber twill
-6mm arms, 2mm plates
-Camera protection
-Ultra Small Profile
-Lightweight designed and durability
-19*19mm mounting size camera only
Specifications
-Airbot OMNIBUS F4 V6 flight controller
-Airbot Furling32 F3 4in1 BLHeli_32 ESC 45A
-Hobbymate Motors: 2207+ 2250Kv support both 4-6S power
-25-600mw switchable 48ch VTX support Smart Audio
-Caddx Turbo Micro SDR2 fpv racing camera
-Foxeer Lollipop 3 2.5DBi 5.8G Super Mini Antenna
Assembly Diagram Download Here
Hobbymate 2207+ FPV Racing Competition Motor
KV: 2250KV 4-6SVersion: CW Screw Thread
Configuration: 12N14PStator Diameter: 22mm
Stator Length: 7.5mm
Shaft Diameter: 4mm
Idle Current(10V): 1.5A
Max. Con. Power 1000W
Max. Current(30s): 40A-45A
Motor Dimension(Dia*Len):21.7x31.5mm
Weight: 30g ( 3cm wire)
Motor Dimension(Dia*Len):21.7x31.5mm
Weight: 30g ( 3cm wire)
Newest version airbot F4 V6
-Omnibus Fireworks firmware (OMNIBUSF4FW target)
-5 UARTS
- Betaflight OSD
-5V1A BEC on board(3-6s) and 1x 8V BEC for Camera/VTX
-MPU6000 at SPI bus, Ext, SPI for damped gyro
-SBUS/PPM input (Pinheaders)
-6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
-Barometer BMP280
-36x36mm, mount holes 30.5x30.5mm
Airbot Furling32 4in1 45A ESC
New BLHELI32 ESC with F3 MCU, give more smooth control and faster responding speed.
Supports up to 55A burst and 45A continued.
Features:
- 32bit ESC with BLHELI32 firmware
- Supports 3-6S lipo input
- PWM input, TLM supported
- Voltage output (VBAT)
- NO BEC
- Supports oneshot / Multishot / Dshot PWM
- Mounting holes 30.5x30.5mm
- Supports damped light
- F3 MCU, runs double faster than F051
- Extra Cap needed for high current or 6s usage
VTX
-Input Voltage: 7-24V DC (6s compatible)
-Frequency: 5.8G
-Channel: 48 (including RaceBand)
-Channel Select button
Video Format: NTSC / PAL
Power Transmission: 0mW / 25mW / 200mW / 400mW /600mW Switchable
Size (mm): 36 x 36 x 5mm
Weight: 6g (Does not contain antenna)
Connector Type: MMCX Connector
Connector Type of Cable: SMA
Smart Audio Protocol: IRC Tramp
RX:
HOBBYMATE Full range receiver D16 mode compatible with Frsky Radio Transmitter, Jumper T16 Transmitter
http://hobbycool.com/full-range-s-bus-receiver-16-ch-support-lua-script-w-s-port-telemetry/
Connection wire diagram for Vtx, Receiver
